Gefen GTV-ETH-2-PLC Manual de usuario Pagina 1

Ethernet Over PLCUser Manualwww.gefentv.comGTV-ETH-2-PLC

7RECEIVER PANEL DESCRIPTIONS1. Standby ButtonPressing this will put the receiving unit in standby mode. The unit will not transfer any information to

8How to Connect the GefenTV Ethernet Over PLCInstallation of the GefenTV Confi guration Assistant1. Insert the included installation CD-ROM into your

9GEFENTV ETHERNET OVER PLC SOFTWARE INSTALLATION5. Close all other applications and press the Next button to continue.6. Please read the license agr

107. Please choose the program installation destination. The default location is “C:\ Program Files\Gefen TV Ethernet Over Power Line”. To set your o

111. Connect the source (i.e. computer, router, switch) to the GefenTV Ethernet Over PLC sender unit using the supplied CAT-5e cable.2. Connect the

12Once both the sending and receiving units are linked and powered, basic confi guration can proceed. This section of the manual refers to the sending

13CONFIGURING THE GEFENTV ETHERNET OVER PLC6. Once all possible nodes have been detected, the program will display all of these nodes as in the windo

14CONFIGURING THE GEFENTV ETHERNET OVER PLC8. The PLC node confi guration screen is separated into the following items:NET IDThis is the name of the ne

15CONFIGURING THE GEFENTV ETHERNET OVER PLC9. Once the update is complete, a message will appear to indicate the update was successful. Click on the

16CONFIGURING THE GEFENTV ETHERNET OVER PLC11. Once the confi guration for the remote node is complete, the local node will then have to be confi gured

ASKING FOR ASSISTANCETechnical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM Monda

17AUTOMATIC SECURITY CONFIGURATION FEATURETo quickly setup the Gefen TV Ethernet Over PLC for secure use, the Automatic Security Confi guration Mode (A

18AUTOMATIC SECURITY CONFIGURATION FEATURE1. Connect the computer with the installed Gefen TV software to the node you wish to set as the Master node

19ADVANCED CONFIGURATIONThere are optional advanced settings that can be confi gured for each node. The advanced menu can be accessed directly through

20ADVANCED CONFIGURATIONFirmware UpdateThis section is used to update the node’s fi rmware from a server location. Please see the Firmware Update secti

21ADVANCED CONFIGURATIONMULTICASTIGMP MulticastThis option will enable or disable the node’s ability to transmit IGMP multicast data.SECURITYThe secur

22ADVANCED CONFIGURATIONVLANThis option will enable or disable the node’s ability to accept VLAN data. If this feature is enabled on one of the nodes,

23ADVANCED CONFIGURATIONADVANCED QOSQOS (quality of service) prioritization. Rule 1 will be applied to all packets fi rst and then Rule 2. Prioritizati

24WEB CONFIGURATIONIf an IP address has been set in the ADVANCE CONFIGURATION PANEL, access to the WEB UTILITY will be enabled. To access the WEB UTIL

25WEB CONFIGURATIONMAIN PAGEThe main page will display general confi guration information. Clicking on the further information link will navigate to a

26WEB CONFIGURATIONThe confi guration options are as follows:MAC Confi gurationNetwork Confi gurationMulticast Confi gurationVLAN Confi gurationPriority Co

CONTENTS1 Introduction2 Operation Notes3 Features4 Sender Panel Layout5 Sender Panel Descriptions6 Receiver Panel Layout7 Receiver Panel Descripti

27FIRMWARE UPDATE PROCEDUREThe fi rmware for the GefenTV Ethernet Over PLC can be updated by FTP, TFTP, or a direct fi le. The fi rmware update can be ex

28Standard Support ... UPA DHS (200 Mbps) PLCInterface ... One P

29WARRANTYGefen warrants the equipment it manufactures to be free from defects in material and workmanship.If equipment fails because of such defects

20600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefentv.com [email protected] X3

Congratulations on your purchase of the GefenTV Ethernet Over PLC. Your complete satisfaction is very important to us.Gefen TVGefen TV is a unique pro

READ THESE NOTES BEFORE INSTALLING OROPERATING THE GEFENTV ETHERNET OVER PLC• This device passes all 10/100BASE-T Ethernet network protocols (TCP/IP,

3Features• Supports up to 200 Mbps data transmission rate• Extension of up to 200 feet (60 meters)• Web confi guration for easy maintenance• Feature

4Front PanelBack PanelTop Panel1423Top Panelp567SENDER PANEL LAYOUT

5SENDER PANEL DESCRIPTIONS1. Standby ButtonPressing this will put the sending unit in standby mode. The unit will not transfer any information to the

6Front PanelBack PanelTop Panel1423Top Panelp5778910RECEIVER PANEL LAYOUT