Gefen GTV-ETH-2COAX Manual de usuario descargar pdf (Pagina 21)

1

8

AUTOMATIC SECURITY CONFIGURATIO

N

1.

C

onnect the computer with the installed

G

e

f

en TV so

f

tware to the node

y

ou

wi

s

h t

o

se

t

as

th

e

M

as

t

e

r n

ode

.

2. Press and hold the

S

ecurit

y/

Reset button on the node

(

A

SC

M

)

, located on

the

f

ront panel,

f

or approximatel

y

2 seconds. The Power LED should be

g

in

to

ﬂ

ash RED, then release the button.

3

.A

f

ter approximatel

y

30 seconds, the Power LED should stop

ﬂ

ashin

g

and

g

low solid RED. This indicates that it is now a Master node. I

f

this node was

a

S

lave node

(

normal node

)

be

f

ore this process, it will now have a randoml

y

g

enerated A

SC

II Net ID and Encr

y

ption Ke

y

set.

4.

O

pen the

G

e

f

en TV

C

on

ﬁ

g

Tool

(

pa

g

e 12

)

. There should be a random

A

SC

II value as the Net ID. I

f

y

ou wish to use this Net ID

f

or the other

S

lave

n

odes, proceed to step 5.

O

therwise,

y

ou can now set

y

our own Net ID and

e

ncr

y

ption password which will be applied to all o

f

the

S

lave nodes in the

n

ext step. To do this, click on the local

“

ETH connected node” MA

C

address

and press the next button.

C

han

g

e onl

y

the Net ID and encr

y

ption password

ﬁ

elds and click on the next button.

O

nce the local node has been updated,

p

roceed to step 5.

5

. For this step to complete success

f

ull

y

, both the Master and

S

lave nodes

h

ave to be in A

SC

M. To do this, press and hold the

S

ecurit

y/

Reset button on

the Master node

f

or approximatel

y

2 seconds. The Power LED should be

g

in

ﬂ

ashin

g

RED. Within 30 seconds, press and hold the

S

ecurit

y/

Reset button

on the

S

lave node

(

s

)

f

or 2 seconds to enter A

SC

M. The

S

lave node’s Power

LED should also be

g

in to

ﬂ

ash while it receives the Net ID and Encr

y

ption

Ke

y

in

f

ormation

f

rom the Master node.

O

nce the Power LED on both the

M

aster and

S

lave nodes stop

ﬂ

ashin

g

and

g

low solid, the setup will be

c

omplete.

C

heck this b

y

openin

g

the

G

e

f

en TV

C

on

ﬁ

g

Tool and seein

g

that

a

ll n

odes

h

a

v

e

th

e

sa

m

e

N

e

t ID.

NOTE: I

f

the

S

lave nodes are located at a

g

reat distance

f

rom the Master node,

it is recommended that

S

tep 5 be repeated

f

or each

S

lave node separatel

y

.

The window that each device remains in A

SC

M is onl

y

30 seconds, and it ma

y

n

ot be possible to put all

S

lave nodes in the A

SC

M within the time

f

rame. It is

also possible to temporaril

y

relocate the

S

lave nodes to a coaxial port closer

to the Master node

f

or this con

ﬁ

g

uration process, and then move them to their

p

ermanent location a

f

ter this process is complete. I

f

a

S

lave node is accidentall

y

s

et as a Master node,

y

ou can hard reset the node b

y

pressin

g

and holdin

g

the

S

ecurit

y/

Reset button

f

or approximatel

y

10 seconds. This will revert the node to a

S

lave node and reset all internal con

ﬁ

g

urations to

f

actor

y

settin

g

s.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 32 33

Comentarios a estos manuales

Sin comentarios