Gefen EXT-DVIKVM-441DL Manual de usuario

www.gefen.com®4x1 DVIKVM DL/SLSwitcherEXT-DVIKVM-441DLUser Manual

7RMT-4IR REMOTE CONTROL DESCRIPTIONLED IndicatorInputSelectionButtonsThe RMT-4IR remote control will allow the user to choose which of the 4 DVI sourc

8 4X1 DVI KVM DL/SL SWITCHER REMOTE INSTALLATIONTo use the RMT-4IR remote, remove the battery cover on the back of the remote to reveal the battery co

9RMT-4IR REMOTE AND 4X1 KVM SWITCHER CONFIGURATIONHow to Resolve IR Code Confl ictsIn the event that IR commands from other remote controls confl ict wi

10EDID MODESWhat is EDID and what is it used for?Under normal circumstances, an audio/video source device (digital or analog) will require information

11EDID MODESEDID ModesThe diagram below illustrates the 4-position DIP switch bank (containing 4 small white toggle switches as shown). The functions

12DL (DUAL LINK) ONLY MODESDL (Dual Link) Only ModesThe 8-position DIP switch bank located on the underside of the 4x1 DVI KVM DL/SL Switcher can be u

13RS-232 SERIAL CONTROLWhat features are available via the RS-232 serial communications port?The 4x1 DVI KVM DL/SL Switcher can accept commands throug

14RS-232 SERIAL CONTROL COMMANDSRS-232 FeaturesRS-232 remote functions are used to control of this product’s features. Features include input to outpu

15RS-232 SERIAL CONTROL COMMANDS#EDIDDSTOLO FunctionThe #EDIDDSTOLO function reads the downstream EDID and stores into all lo-cal inputs.Syntax:#EDIDD

16RS-232 SERIAL CONTROL COMMANDS#DDCTODS FunctionThe #DDCTODS function routes the input DDC to the downstream EDID (pass-through mode).Syntax:#DDCTODS

ASKING FOR ASSISTANCETechnical Support:Telephone (818) 772-9100 (800) 545-6900Fax (818) 772-9120Technical Support Hours:8:00 AM to 5:00 PM Monda

17RS-232 SERIAL CONTROL COMMANDS#LOEDIDTOBA FunctionThe #LOEDIDTOBA function loads the specifi ed EDID fi le and stores it in a specifi ed EDID bank.Synt

18RS-232 SERIAL CONTROL COMMANDS#LOEDIDTOLO FunctionThe #LOEDIDTOLO function loads the specifi ed EDID fi le to a specifi ed local input.Syntax:#LOEDIDTO

19RS-232 SERIAL CONTROL COMMANDS#PRDSEDID FunctionThe #PRDSEDID function reads the downstream EDID and sends it to the serial port.Syntax:#PRDSEDID pa

20RS-232 SERIAL CONTROL COMMANDSCommandsSimplifi ed syntax was used for command implementation for faster operation with the device: # character – isn’

21RS-232 SERIAL CONTROL COMMANDS2. USING SHORT-CUT CHARACTERS TO CHANGE SETTINGS2.1 HYPERTERMINALtm SETTINGS in Microsoft WindowstmFirst, please set u

22Rack mount ears are provided for installation of this unit into a 1U rack mount space.1. Locate the side screws on the unit.2. Remove the front 2

23SPECIFICATIONSVideo Amplifi er Bandwidth:...2 x 165 MHzInput Video Signal:...

24WARRANTYGefen warrants the equipment it manufactures to be free from defects in materialand workmanship.If equipment fails because of such defects a

NOTES

26NOTES

CONTENTS1 Introduction2 Operation Notes3 Features4 Panel Layout5 Panel Descriptions6 Connecting and Operating The 4x1 DVI KVM DL/SL Switc

27NOTES

Rev A620600 Nordhoff St., Chatsworth CA 913111-800-545-6900 818-772-9100 fax: 818-772-9120www.gefen.com [email protected] product uses

1INTRODUCTIONCongratulations on your purchase of the 4x1 DVI-DL KVM DL/SL Switcher. Your complete satisfaction is very important to us.GefenGefen deli

2OPERATION NOTESREAD THESE NOTES BEFORE INSTALLING OROPERATING THE GEFEN 4X1 DVI KVM DL/SL SWITCHER• The 4x1 DVI KVM DL/SL Switcher will take any of

3FEATURESFeatures• Switches easily between any four DVI-SL or DVI-DL sources with USB 2.0 and audio.• Switches USB 2.0, keyboard &

4Back PanelPANEL LAYOUTFront Panel4 52111137 103126 8 9

5PANEL DESCRIPTIONS1 External IR PortFor connection of external IR extension device such as the Gefen IR Extender (part # EXT-RMT-EXTIR).2 IR Receive

6CONNECTING AND OPERATING THE 4X1 DVI KVM DL/SL SWITCHERHow to Connect the 4x1 DVI KVM DL/SL Switcher1. Connect your computers’ DVI, USB, and Audio s